Salvo Studios S401
All S401 cases have been sold! I have already begun designing the S402 which I have planned for availability late fall 2019.
The S401 is Salvo Studios' flagship product for the mITX form factor. Enjoy the ability to orient the chassis in two different ways thanks to the removable stands (thumbscrews) or update that old HTPC with the horizontal orientation of the S401 without the concern your airflow will be restricted.
Check out our custom wood and acrylic side panels as well as the removable handle!
Shipping to "lower 48" US states is flat $20 fee.
Made In USA
S401 Basic Chassis
- S401 case made from galvanized steel and powder coated fine texture (satin) black
- Steel side panels
- Steel vertical stands (2)
- Standard 16mm white LED power switch (installed)
- 300mm PCIe x16 extender (installed)
- C14 PSU internal cable extender (installed)
- 6 foot power cable
- Front panel USB Type-A/Type-C adapter (installed, 20-pin mainboard header cable included)
- All hardware to mount components (mainboard screws, 2.5" or 3.5" disk drive screws, PSU screws, GPU screws, 60mm fan screws, low profile side panel screws, vertical stand thumbscrews)
Case Specifications
Dimensions (External): 357.124mm x 68.2244mm x 324.358mm (14.06" x 2.686" x 12.777")
Volume (External): 7.902L
Orientations supported: Vertical & Horizontal
Stands: Key-slotted with thumbscrews for easy removal
Compatibility
CPU cooler height restriction: ~52mm
PSU support: SFX, SFX-L
Maximum GPU support: length 305mm, width 140mm, height dual slot (40mm)
Fan support: 2 x 60mm x 15mm, 1 x 60mm x 25mm fan mounting locations
Disk Configurations:
1. 4x2.5"
2. 2x3.5" *
3. 1x3.5" and 2x2.5" **
* Requires single-slot GPU or no GPU installed
** Requires GPU less than 200mm installed
Known Incompatibilities
PSU Compatibility Matrix
Download PDF
Support
S401 Accessories
S401 Removable Handle
Sold out
This handle is specifically designed to mount to the standard stand mounts when the chassis is in the vertical position. It is made from 1" aluminum bar stock and 1/8" sheet metal. Two #6-32 thumbscrews will be included for quickly removing mounting/removing the handle. All handles will be powder coated in the fine texture satin black.
Made In USA
S401 3.5" Disk Stacker (1 set)
These 3.5" disk stackers will allow S401 owners to add 3.5" drives vertically to their existing S401 configuration. These 3.5" stackers will allow for a 2 x 3.5" drive configuration per stack. Made from 0.04" stainless steel, these brackets wilI resist warping/bending and never rust.
If a PCIe device is installed inside your S401, please take note of clearances mentioned below as interference may prevent these from being used if the PCIe device is too long. Two 3.5" stackers cannot be used with any PCIe device due to interference. A single, short PCIe device may be used with one 3.5" stacker. The maximum length of a PCIe device when used with the 3.5" stacker is 200mm.
Made In USA
S401 2.5" Disk Stacker (1 set)
These 2.5" disk stackers will allow S401 owners to add 2.5" drives vertically to their existing S401 configuration. These 2.5" stackers will allow for a 6 x 9.5mm, 5 x 12mm, or 4 x 15mm drive configuration in per stack. Made from 0.04" stainless steel, these brackets wilI resist warping/bending and never rust.
If a PCIe device is installed inside your S401, please take note of clearances mentioned below as interference may prevent these from being used if the PCIe device is too long.
Maximum PCIe Length with 2.5" stackers installed:
1 x 2.5" stacker: 240mm
2 x 2.5" stacker: 115mm
3 x 2.5" stacker: 44mm
Made In USA
60mm x 60mm x 15mm PWM Fan
These are brushless 60mm fans that can be installed in the S401 case for chassis cooling. The specs for the fans are as follows:
Voltage: 12V
Current: 0.24A
Speed: 5833RPM
Air Flow: 27.9CFM
Noise: 35dBA
Watt: 2.88W
Comparable Delta model AFB0612VHC which typically costs up to 3x more.
Made In China
